Service · Targeted testing & verification

The exact test you need, measured and documented.

Targeted testing for HVAC systems, cleanrooms, and controlled environments. Accurate data, calibrated measurements, and clear reports for audits, troubleshooting, and system validation, without committing to a full TAB or CPT.

Delivered with the same calibrated instruments and disciplined method as our NEBB (National Environmental Balancing Bureau) certified TAB and Cleanroom Performance Testing, so even a single test stands up to audit.

Test readoutSPECIALISED ▸ SKUD
Test
Fan static pressure · operating point
498 Pa
450On design550
Fan speed1,455 rpmPass
Operating pointOn curvePass
RotationCorrectPass
Worked to ▸ ISO 14644 ▸ GMP expectations ▸ NEBB procedural principles ▸ ASHRAE-based practices
The service

What specialised testing is for.

Specialised testing is the targeted measurement you call for when you need a specific answer, not a full TAB or CPT engagement.

Sometimes the question is narrow. Is this fan on its curve. Is the room holding pressure. What is the actual sound level at the workstation. Specialised testing gives you exactly that data, measured with calibrated instruments and written up so it is clear what it means.

It is the same disciplined method behind our NEBB-certified TAB and Cleanroom Performance Testing, scaled to the single test, audit, or troubleshooting job in front of you.

Define

Pin down the one question, issue, or audit requirement that actually needs an answer.

Measure

Run the agreed tests to the right method, with calibrated instruments and minimal disruption.

Report

Method, measured results, reference values where applicable, observations, and recommendations.

The test menu

Specialised tests, grouped by discipline.

Order any single test on its own, or combine a few. Each is run to a calibrated method and reported in full.

HVAC & airflow

HVAC & airflow performance

  • Site Acceptance Testing (SAT)
  • Fan Performance Testing
  • Duct Velocity & Traverse Measurements
  • Duct Leak Testing
  • HVAC Performance Assessment
  • Airflow Visualisation (Smoke Testing)
Environment & air quality

Environment, comfort & IAQ

  • Indoor Air Quality (IAQ) Testing
  • Temperature & Humidity Logging
  • Vibration Testing
  • Noise Risk Assessment
  • Illuminance (Lux) Testing
  • Environmental Testing
Containment

Containment & contamination control

  • Room Integrity & Pressure Decay Testing
  • Microbiological Testing
  • Hydrogen Peroxide (H2O2) Fogging
Standards & references ▸ ISO 14644 ▸ GMP expectations ▸ NEBB procedural principles ▸ ASHRAE-based practices ▸ DOSH guidelines ▸ Consultant & project requirements ▸ Project design intent & SOO
Chasing one specific problem?

Tell us what to measure, and we will scope the right test.

Our process

From a single request to a structured report.

The same four-step flow on every job, scaled to the test in front of us.

Define scope

Understand the request, the issue, or the audit requirement, and agree exactly what needs measuring.

Test plan

Review drawings, prior reports, and access constraints, then set the method and acceptance references.

On-site testing

Perform the agreed tests with calibrated instruments and minimal disruption to live operations.

Reporting

Test method, measured results, reference values where applicable, observations, and recommendations.

What you receive

Five sections. Every test, every time.

However narrow the scope, the report is built the same way, so a single measurement carries the same weight as a full programme.

Specialised test report · contents 5 sections · calibrated throughout
01

Test method statement

What was tested, how, with which instrument, and against which reference. Written before the test, not reconstructed afterwards, so the method is auditable in its own right.

02

Measured results

Every reading recorded point by point, at the location it was taken. Raw values, not averages presented as conclusions.

03

Reference values

Where a design figure, standard, or acceptance criterion applies, it sits beside the measurement so the comparison is direct. Where none applies, we say so rather than invent one.

04

Observations

What the data actually shows, including anything noticed on site that the numbers alone would not surface.

05

Recommendations

Clear next steps, and where a finding points beyond the scope you booked, we say that too rather than leave the question hanging.

Behind every figure A calibrated instrument with a traceable certificate, and a method statement that names it.
Why Skud

Targeted scope, full discipline.

A single test still gets the calibrated instruments and documented method behind our certified work.

01 / Flexibility

Only the test you need

No need to commission a full TAB or CPT just to answer one question. Order the measurement that matters and nothing you do not.

02 / Calibration

Data you can defend

Calibrated instruments and a documented method mean every figure is traceable and stands up in an audit or dispute.

03 / Pedigree

Backed by certified testing

The same discipline as our NEBB-certified TAB and Cleanroom Performance Testing, applied to targeted, one-off scopes.

Who this is for

When you only need specific tests, not a full programme.

Used when a targeted measurement answers the question, without commissioning a full TAB or CPT.

M&E consultants & HVAC designers
Main & MEP contractors
Facility managers & owners
Hospitals & HSE teams
Pharmaceutical & GMP facilities
Semiconductor & microelectronics
Labs, R&D & universities
Cleanroom & controlled-environment operators
Common questions

Specialised testing, answered plainly.

Can I book just one test?
Yes. Specialised testing is exactly that: order the single measurement you need, without committing to a full TAB or CPT programme. Tell us the question and we scope just that.
When do people use this instead of full TAB or CPT?
For a targeted audit, troubleshooting a specific problem, validating one parameter, or a pre-check before a larger engagement. When the whole system needs proving to a standard, Testing, Adjusting & Balancing or Cleanroom Performance Testing is the right service, and we will say so.
What do I get at the end?
A clear report covering the test method, measured results, reference values where applicable, observations, and recommendations, so you know what the data means and what to do next.
What standards do you follow?
All measurements use calibrated instruments, and the approach follows the applicable guidance: ISO 14644, GMP expectations, NEBB procedural principles, ASHRAE-based practices, and your project's design intent and sequence of operation.
Get a proposal

Tell us what equipment needs certification.

Share the equipment type, quantity, site location and preferred testing date. A Skud engineer will review the requirements and respond with the applicable tests, certification scope and a clear proposal. Prefer to discuss it first? Message us on WhatsApp.

  • Response within one business day
  • Independent testing to the applicable standard
  • Certificates, labels and findings clearly documented

WhatsApp · Service desks

Contact Form 2 Column